installing_pirlp
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
installing_pirlp [2013/01/31 18:30] – 142.103.194.1 | installing_pirlp [2016/01/26 05:29] (current) – [Prerequisites and Disclaimer] k0kad | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | The following is an email from the IRLP Yahoogroups where the steps to build a PiRLP image were listed. | + | =====Re-installing |
+ | |||
+ | This article describes | ||
+ | Raspberry Pi computer from an existing IRLP node. | ||
+ | |||
+ | If you would like a ready-built and configured system, consider ordering one | ||
+ | direct from IRLP at http:// | ||
+ | and all necessary parts to complete your PiRLP project. | ||
---- | ---- | ||
Line 8: | Line 15: | ||
later. | later. | ||
- | Second thing - This is experimental and not supported. If it breaks something, | + | Second thing - This is experimental and not supported. If it breaks something, |
- | apologize, but I can not forsee | + | the IRLP installs team can try to help, but we can not foresee |
- | can, but can not promise it will all work. | + | IRLP will try to help where I can, but can not promise it will all work. If you |
+ | are not able to troubleshoot the problem on your own, consider ordering a complete | ||
+ | built and configured PiRLP node from the IRLP website: http:// | ||
====Hardware Required==== | ====Hardware Required==== | ||
You will require the following hardware: | You will require the following hardware: | ||
* IRLP Ver 3.0 board | * IRLP Ver 3.0 board | ||
- | * Raspberry Pi Model B (any Revision SHOULD work, tested on a Rev 2) | + | * Raspberry Pi Model B, B+, or Pi2 |
+ | * A **suitable** power supply. Please see [[powering_your_pi|Powering your Pi]] | ||
* DB-25 to IDC 26 parallel cable (or similar) | * DB-25 to IDC 26 parallel cable (or similar) | ||
- | * USB sound card (most all should work, I am using the one listed below) | + | * Compatible |
* 2G (min) SD card (larger is better, but not required) | * 2G (min) SD card (larger is better, but not required) | ||
* USB keyboard (for initial boot only) | * USB keyboard (for initial boot only) | ||
+ | * HDMI capable monitor, or an HDMI adapter to another style of monitor | ||
====Required USB Sound Card==== | ====Required USB Sound Card==== | ||
Line 41: | Line 52: | ||
====Hardware Modifications Required==== | ====Hardware Modifications Required==== | ||
+ | |||
The following hardware modifications are required: | The following hardware modifications are required: | ||
- | - Please prepare the IRLP board/ | ||
- | http:// | ||
- | ====Software | + | - Please prepare the IRLP board/ |
- | You will require the official Raspbian release from the Raspberry Pi Foundation: | + | |
+ | A schematic of the cable can be found at this link: [[http:// | ||
+ | |||
+ | Alternately, | ||
+ | |||
+ | http:// | ||
+ | |||
+ | http:// | ||
+ | |||
+ | If you are using a Pi2 or Pi B+ with a 40 pin header, you must cut pins 27 and 28 from the board in order to fit the GPIO cable on. | ||
+ | See: [[http:// | ||
+ | It also shows pin 4 removed - this is not required. It is used as a key for systems ordered from IRLP. | ||
+ | ====Loading the Required | ||
+ | |||
+ | You will require the official Raspbian | ||
http:// | http:// | ||
(no support will be offered for this, besides what buttons to press) Follow the | (no support will be offered for this, besides what buttons to press) Follow the | ||
Line 98: | Line 122: | ||
Your node should work at this point. | Your node should work at this point. | ||
+ | |||
+ | ====Upgrading the Pi Firmware==== | ||
The last step we will do is update the firmware on your Pi. This will help keep | The last step we will do is update the firmware on your Pi. This will help keep | ||
Line 106: | Line 132: | ||
https:// | https:// | ||
- | Start at the step **" | + | Start at the step **" |
+ | been set correctly. The command is: | ||
rpi-update | rpi-update | ||
- | This process will also take several minutes. Then reboot, and enjoy your new PiRLP node. | + | This process will also take several minutes. |
- | + | Then reboot, and enjoy your new PiRLP node. | |
- | If there are questions, please email directly. I will do what I can to help. | + | |
- | Dave Cameron | ||
- | VE7LTD | ||
installing_pirlp.1359657056.txt.gz · Last modified: 2013/01/31 18:30 by 142.103.194.1