Differences

This shows you the differences between two versions of the page.

--- installing_pirlp [2013/01/31 18:34] – 142.103.194.1
+++ installing_pirlp [2016/01/26 05:29] (current) – [Prerequisites and Disclaimer] k0kad
@@ Line 1: / Line 1: @@
-The following is an email from the IRLP Yahoogroups where the steps to build a PiRLP image were listed.
+=====Re-installing IRLP on a Raspberry Pi=====
+This article describes the steps required to re-install IRLP and Debian onto a
+Raspberry Pi computer from an existing IRLP node.
+If you would like a ready-built and configured system, consider ordering one
+direct from IRLP at http://irlp.net/order.html they also have prefabricated
+and all necessary parts to complete your PiRLP project.
 ----
@@ Line 9: / Line 16: @@
 Second thing - This is experimental and not supported. If it breaks something,
-the IRLP installs team can try to help, but we can not forsee all possible issues.
+the IRLP installs team can try to help, but we can not foresee all possible issues.
-I will try to help where I can, but can not promise it will all work.
+IRLP will try to help where I can, but can not promise it will all work. If you
+are not able to troubleshoot the problem on your own, consider ordering a complete
+built and configured PiRLP node from the IRLP website: http://irlp.net/order.html
 ====Hardware Required====
 You will require the following hardware:
   * IRLP Ver 3.0 board
-  * Raspberry Pi Model B (any Revision SHOULD work, tested on a Rev 2)
+  * Raspberry Pi Model B, B+, or Pi2
   * A **suitable** power supply. Please see [[powering_your_pi|Powering your Pi]]
   * DB-25 to IDC 26 parallel cable (or similar)
-  * USB sound card (most all should work, I am using the one listed below)
+  * Compatible USB sound card. Please see [[compatible_usb_sound_cards|IRLP Compatible USB Sound Cards]]
   * 2G (min) SD card (larger is better, but not required)
   * USB keyboard (for initial boot only)
+  * HDMI capable monitor, or an HDMI adapter to another style of monitor
 ====Required USB Sound Card====
@@ Line 44: / Line 54: @@
 The following hardware modifications are required:
-- Please prepare the IRLP board/parallel cable as shown at:
-http://www.irlp.net/R_Pi/
+- Please prepare the IRLP board/parallel cable as shown at: http://www.irlp.net/R_Pi/
+A schematic of the cable can be found at this link: [[http://wiki.irlp.net/lib/exe/fetch.php?media=raspberrypi_to_irlp_interface_schematic.pdf]]
+Alternately, you can view these two YouTube videos:
+http://www.youtube.com/watch?v=1jOxalmll1o
+http://www.youtube.com/watch?v=G-1VxMMATh0
+If you are using a Pi2 or Pi B+ with a 40 pin header, you must cut pins 27 and 28 from the board in order to  fit the GPIO cable on.
+See: [[http://www.irlp.net/R_Pi/P2010014.JPG]]
+It also shows pin 4 removed - this is not required. It is used as a key for systems ordered from IRLP.
 ====Loading the Required Software====
-You will require the official Raspbian release from the Raspberry Pi Foundation:
+You will require the official Raspbian Jessie Lite release from the Raspberry Pi Foundation:
 http://www.raspberrypi.org/downloads
 (no support will be offered for this, besides what buttons to press) Follow the